Enjoy the scent of incense along with the peaceful smile of Buddha. I hope you will have a peaceful time watching the smoke rising from behind Buddha's head.
BUDA INCENSE CONE CHAMBER
This incense chamber is designed to light an incense cone, place it on a stand, and cover the Buddha's face with it to enjoy the smoke rising.
It is finished with coral pink glaze, and the inside is finished with transparent glaze.
After checking that all the incense cones have been burned, throw them away. Occasionally, there may be embers at the bottom of the incense cone.
* When using incense cones, proper ventilation is required. Please use them in a space with airflow.
Please refer to the video when using the incense chamber.
*Check the image above for the actual product you are purchasing.
PRODUCTION PROCESS
MUTA's ceramic products are handmade. After pouring mud water into a specially made plaster mold in the shape of the Buddha, the shape of the Buddha is drawn out, and then all parts, including the hair, face, and ears, are trimmed with a knife and smoothened with a brush. After drying for 7 to 10 days, it is first fired in a kiln at 800 degrees, polished again with fine sandpaper, then glazed with a brush two to three times and fired twice in a kiln at 1,250 degrees. All ceramic products require concentration and effort to produce the best results.
PRODUCT INFO
CERAMIC
COVER: 9.5x10.5x17 cm, CONE PLATE: 11x11x2 cm
PRECAUTIONS
The information below cannot be a reason for exchange or refund, so please fully understand and purchase it.
- The whole process is handcrafted by the artist, and there may be minute differences in patterns, shapes, and sizes.
- Glaze flow marks, small bubble marks, and small dots due to iron components are natural phenomena that occur during glaze and firing.
- In the case of ceramic supports, they may not be perfectly flat due to slight distortion during the high-temperature firing process.
- Pottery products can cause fine cracks on the surface as they are used.
- The above description is a natural phenomenon that occurs during the handmaid process, so it is not defective.
BUDA INCENSE CONE CHAMBER
This incense chamber is designed to light an incense cone, place it on a stand, and cover the Buddha's face with it to enjoy the smoke rising.
It is finished with coral pink glaze, and the inside is finished with transparent glaze.
After checking that all the incense cones have been burned, throw them away. Occasionally, there may be embers at the bottom of the incense cone.
* When using incense cones, proper ventilation is required. Please use them in a space with airflow.
Please refer to the video when using the incense chamber.
*Check the image above for the actual product you are purchasing.
PRODUCTION PROCESS
MUTA's ceramic products are handmade. After pouring mud water into a specially made plaster mold in the shape of the Buddha, the shape of the Buddha is drawn out, and then all parts, including the hair, face, and ears, are trimmed with a knife and smoothened with a brush. After drying for 7 to 10 days, it is first fired in a kiln at 800 degrees, polished again with fine sandpaper, then glazed with a brush two to three times and fired twice in a kiln at 1,250 degrees. All ceramic products require concentration and effort to produce the best results.
PRODUCT INFO
CERAMIC
COVER: 9.5x10.5x17 cm, CONE PLATE: 11x11x2 cm
PRECAUTIONS
The information below cannot be a reason for exchange or refund, so please fully understand and purchase it.
- The whole process is handcrafted by the artist, and there may be minute differences in patterns, shapes, and sizes.
- Glaze flow marks, small bubble marks, and small dots due to iron components are natural phenomena that occur during glaze and firing.
- In the case of ceramic supports, they may not be perfectly flat due to slight distortion during the high-temperature firing process.
- Pottery products can cause fine cracks on the surface as they are used.
- The above description is a natural phenomenon that occurs during the handmaid process, so it is not defective.
